Showing results: 3436 - 3450 of 5217 items found.
-
DP-1200-18 -
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
40-196-101 -
Pickering Interfaces Ltd.
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
40-196-001 -
Pickering Interfaces Ltd.
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
NI
NI software suites aggregate the most popular LabVIEW add-ons and other application software typically combined with LabVIEW and other development environments to help you build test, design, and control applications. Each suite, excluding the Multi-IDE Bundle and the Software Platform Bundle, also includes one year of unlimited access to professional training and certification.The suites come with related NI device drivers and are shipped on USB 3.0 media to speed up your installation.The NI Automated Test Software Suite combines LabVIEW, LabWindows/CVI, and Measurement Studio with the TestStand ready-to-run, customizable test executive and the Switch Executive intelligent switch management and routing application to help you build manufacturing or production test systems.The NI Embedded Control and Monitoring Software Suite features LabVIEW and the recommended add-ons specifically for building embedded control and monitoring systems on NI reconfigurable I/O (RIO) hardware. The LabVIEW FPGA Module extends the LabVIEW graphical development platform to target FPGAs on NI RIO hardware, and the LabVIEW Real-Time Module builds on LabVIEW to deliver a programming environment for creating reliable, deterministic, and stand-alone embedded systems.The NI HIL and Real-Time Test Software Suite combines LabVIEW with VeriStand, a configuration-based software environment for efficiently creating real-time test applications. It also includes the LabVIEW Control Design and Simulation, LabVIEW Real-Time, and LabVIEW FPGA modules.To learn more about each suite, use the navigation options on the left side of the page.The mark LabWindows is used under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
-
Pickering Interfaces Ltd.
Pickering's range of high-density switch matrix modules is a cost-effective solution for applications that require high-density matrices in the PXI format. The ability to expand to larger matrices is possible by connecting together multiple modules. Reed relay versions use high quality sputtered ruthenium reeds that exhibit excellent contact performance under low and medium level switching conditions, solid-state relay versions available for high speed and long life and electro-mechanical versions for current handling up to 2 Amps. Select models are supported by Pickering's Diagnostic Test Tools, Built-In-Relay-Self-Test (BIRST) and eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
33950 -
S & G Tool Aid Corp
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
BDL-3927 -
Kongter Test & Measurement Co., Limited
BDL-3927 is updated Battery Data Logger to meet IEEE measurement standards for battery voltage, string voltage, current and ambient temperature. It is customized from 12V to 700V for different battery systems. And it has easy expansion for all battery systems. With wifi communication, you could easily view complete data and generate test report in the PC software.
-
Yelo Ltd.
The Yelo LIV test instrument allows LIV measurements to be taken from laser devices loaded into a Yelo module. This module can also be used with the Yelo Y1000L Low Power Burn-in system. The LIV test instrument has been designed for easy operation. Once powered on, and with laser supply enabled, the touch screen can be used to initiate, monitor and review measurements of laser devices.
-
MM14 -
D.Marchiori s.r.l.
The MM14 is a digital technology pressure standard calibrator. It consists of a variety of components combined to allow ease of operation for the verification of pressure based UUTs (unit under test) such as Air Data Test Sets.The MM14 utilises a very accurate dual pressure transfer standard generator, a reference Primary Standard dead-weight and PC based operating system for automatic verification of the U.U.T.
-
N39400 Series -
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N39400 series is a high-accuracy & multi-channel programmable DC power supply with standard 19-inch 2U design, available for cabinet installation. Single N39400 supports Max. 4 channels output, with channels isolated. Both local operation on front panel and remote control on a computer are supported. N39400 can be widely used in lab test, system integration test, production aging line, etc.
-
MCV -
Bitrode, Inc.
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Neutronics Manufacturing Co.
Our Earth Tester is a very successful replacement of the conventional generator type hand tester. This device is most extensively used to test the earthing installation in numerous power based industries, electrical traction systems and telecommunication networks.
-
LP Technologies
LPT-3000 Portable Spectrum AnalyzerThe LP Technologies LPT-3000 Spectrum Analyzer is a fully synthesized RF Spectrum Analyzer featuring simple user controls which allow the novice or the seasoned expert to use the LPT-3000 right out of box. The LPT3000 provides you with a powerful RF test and measurement tool for CDMA and WCDMA RF systems, broadcast RF systems, EMI/EMC. The features include 6.4 color display, centronics printer, internal memory, USB host, built in CDMA measurement (ACP, Channel Power and Occupied bandwidth). The LPT 3000 Spectrum Analyzer gives educational institutions, mobile and communication system manufactures and RF product service centers a quality RF test instrument at an unbelievably affordable price.
-
Model 3448 -
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
MMR-650 -
Sonel S.A.
Designed to measure very low resistances of both resistive and inductive types of objects, including amorphous core transformers. This product is made to be used in power plants, railways and maintenance companies, to measure welded and soldered connections, equipotential bondings, earthing conductors, contacts, bolted connections, windings of motors and power transformers and other resistive and inductive objects. MMR-650 can be also utilized on a production lines (eg. at the final production control stage). An innovative combination of a high-performance measuring device with a modern user interface and advanced data management system. Wireless data transmission, enhanced system of 2D codes and ability to print labels to identify test items, all contribute to bringing new quality of work and allow the user to perform a wide range of measurements.
